Fiber Coupled Semiconductor Lasers include 105um, 135um, 200um and other different fiber core diameter outputs. The laser power ranges from tens of watts to tens of kilowatts, and the output wavelength covers 400nm to 1000nm. It has multi-single tube coupling, high reliability, and anti-reflection protection. , high photoelectric conversion rate, wide wavelength coverage and other characteristics, it is widely used in industrial processing, precision processing, medical cosmetology, scientific research, sensing detection, lighting and other fields.
This operation guide guides everyone to skillfully operate the semiconductor laser module. Especially for air-cooled laser customers, this standard installation process is particularly important.
Safety Precautions
Under normal circumstances, very little light is scattered from a bent fiber (due to bend loss), which is relatively safe. However, as long as the laser module is powered on, eye protection must still be provided to prevent sudden strong light leakage caused by fiber damage/melting. Please strictly abide by the Level 4 infrared laser safety standards and take protective measures for your eyes and skin.
Circuit Connection
1. Electrostatic Protection
Electrostatic discharge is one of the important causes of unexpected failure of semiconductor lasers. Laser installation must be completed by trained personnel. Anti-static wrist straps must be worn during operation and the workbench must be grounded.
Laser modules are packed with anti-static materials, and the positive and negative electrode leads of each device are short-circuited with static dissipative materials; the anti-static protection wires on the pins can be removed only after the laser module pins are connected to the power supply. .
2. Power Supply
When the voltage or current of the power supply exceeds the maximum allowed value of the laser module (given in the product specification sheet), diode damage may occur. The power supply should have overcurrent and overvoltage protection, as well as transient suppression functions.
When several laser modules are used in series, in order to prevent breakdown between the device and the ground, the maximum voltage across the electrodes is recommended to be less than 75V.
3. Electrode Welding
The "plug and play" power supply method is only suitable for short-term use or testing; for long-term use, please use direct welding for power supply. The maximum temperature of welding cannot exceed 300°C, and the welding time cannot exceed 10 seconds.
Bending or cutting the electrode pins may affect the airtightness and reliability of the laser module, so it is not recommended to bend or cut the electrode pins.
Optical Fiber Finishing
To avoid damage to the fiber, the fiber needs to be coiled. When storing and transporting, the bending radius of the optical fiber should be greater than 200 times the fiber diameter; when the laser is working, the bending radius of the optical fiber should be larger, refer to the table below for details.
| Optical Fiber Type | Store Bend Radius | Optical Fiber Bending Radius When Guiding Light |
| 105/125,106.5/125 | >25mm | >30mm |
| 135/155 | >32mm | >40mm |
| 200/220 | >45mm | >60mm |
| 220/242 | >60mm | >65mm |
For optical power semiconductor lasers with power of 800W and above, the bending radius should be appropriately increased by 20-50%.
Semiconductor Laser Anti-return Light
A two-color filter is installed inside the laser module to prevent ~1 micron band laser from damaging the laser diode, but there are still two situations to consider:
First, the dual-color filter cannot protect against 9XXnm return light or residual pump light (for example, in a bidirectionally pumped fiber laser, not all pump light will be absorbed by the active fiber). In order to avoid damaging the laser diode, the returned 9XXnm light must be controlled within 2.5% of the maximum output power of the laser module.
Secondly, although the two-color filter has a high degree of isolation to protect the laser diode, the ~1 micron return light intensity should be controlled not to exceed the return light processing capability of the laser module. The ~1 micron return light energy in any 1 second cannot exceed 10 Joules (for example: 10 watts of continuous light, or 10 kilowatts of power but lasting less than 1 millisecond).
Semiconductor Laser Testing and Use
1. Output Preparation
Under the maximum driving current, the reflected light from the end face of the output fiber of the laser module returns to the inside of the laser, which may cause the power of the laser diode to degrade, and in severe cases, directly cause the laser to fail. In order to avoid damaging the laser, before testing the output power of the laser module, you need to splice an output fiber coated with antireflection coating on its output fiber, or cut or grind the output fiber end face to an 8° bevel angle, and then test Output Power again.

2. Laser Driving Method
It is generally considered that the reliability of a laser diode is related to the percentage of the laser usage time at a specific power of the optical module to the total operating time. However, considering the diversity of each customer's actual application methods, such as using different driving methods such as continuous operation and pulse operation (different rise/fall times, duty cycles, frequencies, etc.). Such a wide parameter space makes it impossible to completely Set up and build reliability models in different modes.
In order to avoid reducing the reliability of the laser, the laser is required to be installed on a cooling plate at about 25°C, and at the same time ensure that the peak operating current does not exceed the rated maximum current; especially in pulse operating mode, current overshoot must be avoided; if the laser operates in pulse mode for a long time , we recommend that the laser drive rise/fall time should be greater than 10μs, and the modulation frequency should not exceed 50KHZ.
3. Power Test
It is recommended to use the following equipment and instruments for power measurement:
Laser power meter: OPHIR_ NOVA II
1-100W output power level laser detector: OPHIR_ L50(150)A-PF-35
1-1000W output power level laser detector: OPHIR_1000W-BB-34-V3
Contact information:
If you have any ideas, feel free to talk to us. No matter where our customers are and what our requirements are, we will follow our goal to provide our customers with high quality, low prices, and the best service.
Email:info@loshield.com
Tel:0086-18092277517
Fax: 86-29-81323155
Wechat:0086-18092277517








