Application Of Semiconductor Laser in PM2.5 Dust Sensing Technology

Jan 16, 2024 Leave a message

The application of Semiconductor Lasers in PM2.5 dust sensing technology has become more and more common. In order to pursue higher performance, modern PM2.5 sensors have begun to introduce laser technology, especially low-power semiconductor lasers, to replace traditional infrared LED light sources. Laser sensors offer several advantages over infrared LED sensors. First, they can provide greater accuracy and stability. In addition, because semiconductor lasers can operate stably for a long time within a wide range of ambient temperature changes, they place higher requirements on the overall reliability of the laser.

Dust detection technology was first born in the 1950s. Developed countries represented by the United Kingdom, the United States, Japan, and Germany took the lead in carrying out relevant research and applying it to industrial and mining dust monitoring and other scenarios to control and prevent causes caused by respirable dust. various occupational diseases. After decades of development, dust detection technology based on the principle of light scattering has gradually entered civil fields such as air purifiers. Since the 21st century, with the acceleration of China's industrialization process, the problem of environmental pollution as a by-product has become increasingly prominent. The respiratory health of urban residents has been affected by the haze problem. Therefore, particulate matter pollution detection technology represented by "PM2.5" has also It entered the public eye for the first time and became a key topic of widespread social concern. PM2.5 sensors have gradually become an important tool for air quality detection indoors, in cars, and in public places.

laser sensor

Early dust sensors mainly used infrared LEDs as light sources and generated heat through resistors to obtain hot air flow. When particles in the air pass through, they are scattered after contacting the LED light source. After being received by the photosensitive detector, electrical signals of different sizes are generated. After amplification and calculation, the detection results are obtained. In this technology, due to the low intensity of LED scattered light and the weak air flow generated by the heating resistor, it is usually only effective for larger particles with a diameter greater than 1 μm, and the changes in particulate matter in the air can only be characterized by the duty cycle of the electrical signal. The measurement numerical error is large, and it cannot adapt to the changing environment of dust sources, making it difficult to achieve real-time monitoring of particulate matter such as PM2.5.

In pursuit of higher performance, PM2.5 sensors began to introduce laser technology, using low-power semiconductor lasers as light sources to replace the original infrared LEDs. The sampling air is pushed into the area where the laser beam is located through a fan or blower. The particles in the air scatter the laser, and the scattering angle and light intensity distribution of particles of different particle sizes are different. By installing photosensitive detectors at different locations, the particles are collected separately. The light is scattered and converted into electrical signals. After analysis, the concentration of particles of different sizes can be quickly obtained, thereby achieving high-precision measurement. Compared with infrared LED sensors, laser sensors have the following advantages:

Project IR LED sensor Laser sensor
Detect particle size >1μm >0.3μm
Measuring range 0-300μg/m³ 0-1000μg/m³
Measurement accuracy Working under a single dust source, the error will be large after the dust source changes Can meet different dust sources, accuracy 10%
Output signal Analog signal, low level duty cycle, easy to distort Digital signal, output PM1.0/PM2.5/PM10 concentration value
Response time average 30 seconds 1 second
Maintenance It is prone to dust accumulation and requires regular scrubbing and maintenance. No post-maintenance required
Application scenarios Low-precision, single dust source, large-diameter particle concentration change trend detection, such as mines, pipeline dust detection, vacuum cleaners, etc. High-precision, composite dust source, particle concentration testing of different diameters, such as central air conditioners, vehicle air conditioners, air purifiers, oil fume sensors, dust monitoring, etc.

In addition to indoor appliances, there is also an increasingly strong demand for PM2.5 detection in cars and outdoor environments. In the face of more complex use environments, the low-power semiconductor laser used in the sensor is not only required to have stable light output, but also to work for a long time in a wide range of ambient temperature changes. Therefore, higher requirements are put forward for the overall reliability of the laser. In the early days, most PM2.5 sensors used imported brands. In recent years, key technological breakthroughs have been made in the research and development of JTBYShield semiconductor lasers, which combine high-reliability epitaxial structure design and growth, high-quality cavity coating process, fully-automatic gold-tin eutectic process, and fully-automatic aging. Advanced technologies such as and test binning have been introduced into the field of low-power semiconductor laser manufacturing. Low-power semiconductor laser products represented by 650nm and 790nm can operate stably in harsh environments ranging from -40°C to 85°C. They have been used in PM2. 5 detection field has been recognized by leading companies in the industry and many customers, and has been widely used in indoor and outdoor and vehicle-mounted PM2.5 sensors for many years.

laser diode

Contact information:

If you have any ideas, feel free to talk to us. No matter where our customers are and what our requirements are, we will follow our goal to provide our customers with high quality, low prices, and the best service.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry